CANtieCAR – J2534 HW – Diagcode edition

Hardware (USB + Bluetooth + WiFi) 
– Powerful CortexM4-core MCU
– Wi-Fi chipset ESP8266EX
– Bluetooth v2.0 + EDR + BLE
– True USB-ready device: CDC, FT232B/R-emulation, FT2232C-emulation, MSD over SD Card
– SD Card: internal Flash storage with USB-MSD up to 32GB
– 3 independent ISO9141/ISO14239 K-Lines (ISO-Lines): OBDII-pins 7,8,15
– 2 multi-functional lines (MFLs): CAN – one and two-wires, K Lines, J1850, DC-DC-out (5-30V)/1W etc.
– 3 CAN channels at the same time: Dual Wire CAN, Fault-tolerant CAN, Single wire CAN
– SAE J1850 Normal and High Speed support: J1850PWM 41.6 Kbps and 83.3 Kbps; J1850VPW 10.4 Kbps and 41.6 Kbps
– built-in analog switches multiplexer for OBDII-pins 1,2,3,6,8,13 and 8,9,10,11,12,14 with cross-link for the MFLs
– built-in hardware UART multiplexer
– built-in switchable CAN-bus differential terminator 120 Ohm
– 9 Leds: 6 – Bus Activity, 1 bi-color – USB/Bluetooth/Wi-Fi TX Activity + Status, 1 bi-color – Power state: USB and car + USB Activity, 1 bi-color – Bluetooth/Wi-Fi Status/Activity
– 2 DC-DC: 5V/500mA and programmable (5-35V)/1W
– 8 ADC Channels: Power ISO-Lines, Power MFL, High MFL, Low MFL, OBD:1, OBD:8, OBD:9, OBD:16
– Systems: Up to 35V
– Speed: ISO-Lines up to 1Mbit/s; CAN up to 1Mbit/s
– Special OBDII-connector design
– Security Firmware updates
– ALL protections with Resetable fuses

PassThru SAE J2534-1/2 Support
– J1850VPW, J1850VPW_PS
– J1850PWM, J1850PWM_PS
– ISO9141, ISO9141_PS
– ISO14230, ISO14230_PS
– CAN, CAN_PS
– ISO15765, ISO15765_PS
– SW_CAN_PS, SW_ISO15765_PS
– FT_CAN_PS, FT_ISO15765_PS
– UART_ECHO_BYTE_PS
– HONDA_DIAGH_PS
– UBP_PS (UBP – Ford UART Based Protocol)

Specification – Supported mode

– USB-Serial (4/5:GND, 6:CTS, 7:RXD, 8:DTR/DSR, 14:RTS, 15:TXD)

– USB-Serial Inverted (4/5:GND, 6:~CTS, 7:~RXD, 8:~DTR/~DSR, 14:~RTS, 15:~TXD)

– K-Line + USB-Serial LPG/CNG (4/5:GND, 12:RX/L, 13:TX/K, 7:K) !!! 2 Virtual COM-Ports !!!

– KL-Line (7:K, 15:L)

– 2K-Line (7:K, 15:K2)

– KKL-Line (7:K, 15:L/K2)

– 3K-Line (7:K, 15:K2, 8:K3)

– OPEL 4K-Line (7:K, 8:K3, 3:K4, 12:K5)

– Multiplexed K-Line to ALL OBD-pins